Current transformer home >> Transformer news >> Power transformers: March 2010
Monday, March 29, 2010
 The variable auto-transformer is capable of fluctuate the voltage to the secondary circuit. There will be a number of windings used for the primary & secondary and are separated with the help of using a dial. Variable Auto-transformer is generally making use of all the way through low voltages and care for arcing because of the closeness of the primary and secondary windings. As a substitute of resistance these auto-transformer make use of inductance to vary on how much power have taken by every circuit. These auto transformers are grand for testing of any electrical equipment. They are able of verify for the potential high responsible currents by their slowly growing volts from zero up. These transformers are able to perform lesser & greater voltage experiments. Even if the key input is very high or very low they are adjust to provide average 240 volts AC production. Standard output of these transformer starts from 10 amp GPO and they has output defending circuit breaker. They encompass production post workstation, disconnect earth post visual display unit and hold handles also. Similar like two-winding transformers, autotransformers might be prepared with a lot of regulators and mechanical switchgear to permit them to proceed as an automatic regulator.
posted by Custom Power Transformer News @ 10:11 AMpermanent link | |
0comments
Tuesday, March 23, 2010
 Step-down transformers are most usually made used to convert the 220 volt of electric current that is seen in almost allover the world to the 110 volts necessary by North American electrical gears and apparatus. For instance, the electrical appliances those are well-liked with American emigrant who don’t like to dump their American appliances while they migrate to Europe. Regrettably step-down transformers might turn out to be dangerous when not handled with proper caution and knowledge of installing them. Almost all step-down transformers are in point of fact autotransformers. To be clearer we can say that these transformers have only a solitary winding and a center tap while normally there must be two separate, electrically cut off windings. It is best and advisable never to use a surge protector on the 110 volt side of a 220-to-110 volt step-down transformer. All the appliances that are to be used must be wired properly in accord with the wiring diagram that is given along with it. Always disconnect supply voltage before starting to workout on anything or during installation.
posted by Custom Power Transformer News @ 10:56 AMpermanent link | |
0comments
Monday, March 22, 2010
 In the step-down transformer secondary voltage will be lesser than its primary electrical energy or voltage. This type of transformer specially designed to reduce the electrical energy to the secondary winding from the primary winding. In these steps down transformer the electrical energy will be appropriate to it. This changes high-voltage and low-current power into low-current and high-current power being as a step-down entity. In the secondary winding the larger-gauge cable is used and it is essential due to the raise in power. At the same time as the primary winding that don't require carry out much current might be prepared out of smaller-gauge cable. A step-down can function as a step-up transformer and vice-versa. Often the construction of the transformers will be in such a way that it is not understandable which cables direct to the primary winding and which go ahead to the secondary winding. In this step-down transformer, as verified by the high rotate calculation of the primary winding and the low down rotate count of the secondary windings. If at all you are in doubt than it is probably possible to function either of these transformer types backwards to carry out the contradictory function.
posted by Custom Power Transformer News @ 11:23 AMpermanent link | |
0comments
Thursday, March 18, 2010
 This is the fact that Isolation transformers are able to do step up or step down voltage but they don't perform it involuntarily. Isolation transformers are able to provide various purposes. These types of transformers will be able to divide a circuit into a primary and a secondary circuit and during this process that split will not allow current sound directly. In the midst of the primary and secondary circuit these transformers defend capacitance enhancement and for the reason that, it causes high-frequency sound. Isolation transformer care for ground associations involving the primary and secondary which is not intentional. They can break up the main current from secondary circuit. Consequently it can save from harm by shock and accidental earthlings from high power exclusion. These kinds of transformers have many consequences. An isolation transformer is a type of transformer, repeatedly comes with equal windings. They allow the signal or current to be in use from one apparatus and supply for another one without including electrical connection of the two circuits. Isolation transformers permit AC signals to surpass but building block diffusion of DC signals from one circuit to another. These transformers also block intrusion originated from ground loops.
posted by Custom Power Transformer News @ 10:43 AMpermanent link | |
0comments
Tuesday, March 16, 2010
 Transformers change the current of a broken down circuits. Transformers use to link through a magnetic core by way of two circuits to convert the power. Electrical energy facilitate in altering the power-input circuit to the power-output circuit. The percentage of windings the two circuits put up in the area of the core determines the power of transformation. In step up transformer if you reduce the power than also it will enhance the voltage. Step-up transformer has fewer turnings on the primary coil and more turning on the secondary coil. Consequently the electrical energy induced in the secondary loop is more than the primary loop voltage. To make a better understanding let's see in brief here: NS/NP = VS/VP ,If on the prime loop the number of rotation is NP and on the secondary loop the number of rotation is NS, along with the particular voltages are VP and VS. For example, if there are 2,000 rotations on the secondary loops and 200 turnings on the main loop then the current induce in the secondary loop will be ten times bigger than the main loop current. The utilization of transformers can be placed into two broad modules that contain voltage supply and signal matching.
posted by Custom Power Transformer News @ 10:31 AMpermanent link | |
0comments
| |
Previous Posts
General interest on variable auto-transformer
Caution To Be Followed While Using Step down Trans...
Boost your knowledge on step-down transformer
The integral of isolation transformer
A thought on step-up transformer
Exclusive information on single phase & three phas...
A brief on Transformer
A short note on three phase transformers
A brief note on low voltage electronic transformer...
More about transformers and its testing
Archives
November 2007
December 2007
January 2008
February 2008
March 2008
April 2008
May 2008
June 2008
July 2008
August 2008
September 2008
October 2008
November 2008
December 2008
January 2009
February 2009
March 2009
April 2009
May 2009
June 2009
July 2009
August 2009
September 2009
October 2009
November 2009
December 2009
January 2010
February 2010
March 2010
Current Posts |
